oil Ram 1500 2014 Get to Know Guide 

- Malfunction Indicator Light (MIL)
The Malfunction Indicator Light (MIL) is part of an onboard diagnostic system called
OBD II that monitors engine and automatic transmission control systems. The light
will illuminate when the key is in the ON/RUN position before engine start. If the bulb
does not come on when turning the key from OFF to ON/RUN, have the condition
checked promptly.
Certain conditions, poor fuel quality, etc., may illuminate the light after engine start.
The vehicle should be serviced if the light stays on through several of your typical driving
cycles. In most situations, the vehicle will drive normally and will not require towing.
CAUTION!
Prolonged driving with the Malfunction Indicator Light (MIL) on could cause damage
to the engine control system. It also could affect fuel economy and driveability. If the
MIL is flashing, severe catalytic converter damage and power loss will soon occur.
Immediate service is required.
WARNING!
A malfunctioning catalytic converter, as referenced above, can reach higher tempera-
tures than in normal operating conditions. This can cause a fire if you drive slowly or
park over flammable substances such as dry plants, wood, cardboard, etc. This could
result in death or serious injury to the driver, occupants or others.
- Electronic Stability Control (ESC) OFF Indicator Light
The ESC OFF indicator will illuminate when the Electronic Stability Control (ESC) is
turned off.
- Charging System Light
This light shows the status of the electrical charging system. If the charging system light
remains on, it means that the vehicle is experiencing a problem with the charging
system.
We recommend you do not continue driving if the charging system light is on. Have
the vehicle serviced immediately.
- Oil Pressure Warning Light
This light indicates low engine oil pressure. If the light turns on while driving, stop
the vehicle and shut off the engine as soon as possible. A chime will sound for four
minutes when this light turns on.
We recommend you do not operate the vehicle or engine damage will occur. Have the
vehicle serviced immediately.
WHAT TO DO IN EMERGENCIES
172

- Transmission Temperature Warning Light
This light indicates that there is excessive transmission fluid temperature that might
occur with severe usage such as trailer towing. If this light turns on, stop the vehicle
and run the engine at idle, with the transmission in NEUTRAL, until the light turns
off. Once the light turns off, you may continue to drive normally.
CAUTION!
Continuous driving with the Transmission Temperature Warning Light illuminated
will eventually cause severe transmission damage or transmission failure.
WARNING!
If you continue operating the vehicle when the Transmission Temperature Warning
Light is illuminated you could cause the fluid to boil over, come in contact with hot
engine or exhaust components and cause a fire.
OIL CHANGE EVIC INDICATOR
Message
If an “oil change” message (shown as “Change Oil Soon” and “Oil Change Needed”)
appears and a single chime sounds, it is time for your next required oil change.
Resetting The Light After Servicing
1. Turn the ignition switch to the ON/RUN position (do not start engine).
2. Fully depress the accelerator pedal three times within 10 seconds.
3. Turn the ignition switch to the OFF/LOCK position.
- Low Coolant Level Indicator Light
This light indicates low coolant level. If the light turns on while driving, stop the
vehicle and shut off the engine as soon as possible.
We recommend you do not operate the vehicle or engine damage will occur. Have the
vehicle serviced immediately.
WHAT TO DO IN EMERGENCIES
174

•For 4x2 and 4x4 trucks, when changing a rear wheel, assemble the jack drive tube
to the jack and connect the drive tube to the extension tube. Place the jack under
the axle between the spring and the shock absorber with the drive tubes extending
to the rear.
• Connect the jack tube extension and wheel wrench.
NOTE:
If the bottle jack will not lower by turning the dial (thumbwheel) by hand, it may be
necessary to use the jack drive tube in order to lower the jack.
• By rotating the wheel wrench clockwise, raise the vehicle until the wheel just clears the surface.
• Remove the wheel nuts and pull the wheel off. On single rear-wheel (SRW) trucks, install the spare wheel and wheel nuts with the cone shaped end of the wheel nuts
toward the wheel. On 3500 dual rear-wheel models (DRW) the wheel nuts are a
two-piece assembly with a flat face. Lightly tighten the wheel nuts. To avoid the
risk of forcing the vehicle off the jack, do not fully tighten the wheel nuts until the
vehicle has been lowered.
• Using the lug wrench, finish tightening the wheel nuts using a crisscross pattern. The correct wheel nut tightness is 130 ft lbs (176 N·m) torque (1500 Series),
135 ft lbs (183 N·m) torque for 2500/3500 single-rear wheel (SRW) models, and
140 ft lbs (190 N·m) for 3500 dual rear-wheel models. If in doubt about the
correct tightness, have them checked with a torque wrench by your authorized
dealer or at a service station.
• Install the wheel center cap and remove the wheel blocks. Do not install chrome or aluminum wheel center caps on the spare wheel. This may result in cap damage.
• Lower the jack to its fully closed position. If the bottle jack will not lower by turning the dial (thumbwheel) by hand, it may be necessary to use the jack drive
tube in order to lower the jack. Stow the replaced tire, jack, and tools as previously
described.
• Adjust the tire pressure when possible.
NOTE:
Do not oil wheel studs. For chrome wheels, do not substitute with chrome plated
wheel nuts.
WHAT TO DO IN EMERGENCIES
183

8-Stud — Dual Rear Wheels
• Dual wheels are flat-mounted and center-piloted. The lug nuts are a two-pieceassembly. When the tires are being rotated or replaced, clean these lug nuts and
add two drops of oil at the interface between the hex and the washer.
• Slots in the wheels will assist in prop- erly orienting the inner and outer
wheels. Align these slots when assem-
bling the wheels for best access to the
tire valve on the inner wheel. The tires
of both dual wheels must be com-
pletely off the ground when tightening,
to ensure wheel centering and maxi-
mum wheel clamping.
• Dual wheel models require a special heavy-duty lug nut tightening adapter
(included with the vehicle) to correctly
tighten the lug nuts. Also, when it is necessary to remove and install dual rear
wheels, use a proper vehicle lifting device.
NOTE:
When installing a spare tire as part of a dual rear wheel end combination, the tire
diameter of the two individual tires must be compared. If there is a significant
difference, the larger tire should be installed in a front location. The correct direction
of rotation for dual tire installations must also be observed.
These dual rear wheels should be tightened as follows:
1. Tighten the wheel nuts in the num- bered sequence to a snug fit.
2. Retighten the wheel nuts in the same sequence to the torques listed in the
table. Go through the sequence a
second time to verify that specific
torque has been achieved. Retighten to
specifications at 100 miles (160 km)
and after 500 miles (800 km).
• It is recommended that wheel stud
nuts be kept torqued to specifications
at all times. Torque wheel stud nuts to specifications at each lubrication interval.
WHAT TO DO IN EMERGENCIES
187

FLUIDS AND CAPACITIES
Gasoline Versions
ComponentFluid, Lubricant, or
Genuine Part Capacities
Engine Coolant
3.6L Engine We recommend you use
MOPAR
®Antifreeze/
Coolant 10 Year/150,000
Mile Formula OAT (Organic Additive Technology). 14 Quarts (13 Liters)
Engine Coolant
5.7L 1500 Models We recommend you use
MOPAR
®Antifreeze/
Coolant 10 Year/150,000
Mile Formula OAT (Organic Additive Technology). 16 Quarts (15 Liters)
Engine Coolant
5.7L 2500/3500 Models We recommend you use
MOPAR
®Antifreeze/
Coolant 10 Year/150,000
Mile Formula OAT (Organic Additive Technology) . 18.7 Quarts (17.7 Liters)
Engine Coolant
5.7L 2500/3500 Models
w/Heavy Duty We recommend you use
MOPAR
®Antifreeze/
Coolant 10 Year/150,000
Mile Formula OAT (Organic Additive Technology) . 19.2 Quarts (18.2 Liters)
Engine Coolant
6.4L 2500/3500 Models We recommend you use
MOPAR
®Antifreeze/
Coolant 10 Year/150,000
Mile Formula OAT (Organic Additive Technology) . 18.7 Quarts (17.7 Liters)
Engine Coolant
6.4L 2500/3500 Models
w/Heavy Duty We recommend you use
MOPAR
®Antifreeze/
Coolant 10 Year/150,000
Mile Formula OAT (Organic Additive Technology) . 19.2 Quarts (18.2 Liters)
Engine Oil with Filter
3.6L, 5.7L We recommend you use
API Certified SAE 5W-20 Engine Oil, meeting the
requirements of Chrysler Material Standard
MS-6395 such as
MOPAR
®, Pennzoil®,and
Shell Helix®. Refer to your
engine oil filler cap for correct SAE grade. 3.6L Engine - 6 Quarts
(5.7 Liters)
5.7L Engine - 7 Quarts (6.6 Liters)
MAINTAINING YOUR VEHICLE
205

ComponentFluid, Lubricant, or
Genuine Part Capacities
Engine Oil with Filter 5.7L
For 2500/3500 trucks
operating with a gross
combined weight rating
greater than 14,000 lbs/
(6,350 kg) We recommend you use
API Certified SAE 5W-30 Engine Oil, meeting the
requirements of Chrysler Material Standard
MS-6395 such as
MOPAR
®, Pennzoil®,and
Shell Helix®. Refer to your
engine oil filler cap for correct SAE grade. 5.7L Engine - 7 Quarts
(6.6 Liters)
Engine Oil with Filter 6.4L For best performance and
maximum protection under all types of operating con-ditions, the manufacturer
only recommends full syn-
thetic engine oils that meet the American Petroleum
Institute (API) categories of SN. The manufacturer recommends the use of
Pennzoil Ultra™ 0W-40 or
equivalent MOPAR
®engine
oil meeting the require-
ments of Chrysler Material Standard MS-12633 for use in all operating temperatures. 6.4L Engine - 7 Quarts
(6.6 Liters)
Engine Oil Filter
3.6L, 5.7L, 6.4L We recommend you
use MOPAR
®Engine
Oil Filters. —
Spark Plug 3.6L We recommend you use
MOPAR
®Spark Plugs
(Gap 0.043 in [1.1 mm]) —
Spark Plug 5.7L We recommend you use
MOPAR
®Spark Plugs
(Gap 0.043 in [1.1 mm]) —
Spark Plug 6.4L We recommend you use
MOPAR
®Spark Plugs
(Gap 0.043 in [1.1 mm]) —
MAINTAINING YOUR VEHICLE
206

Diesel Versions
ComponentFluid, Lubricant, or
Genuine Part Capacities
Engine Coolant
3.0 L Turbo Diesel Engine –
1500 Models Only
We recommend you use MOPAR®Antifreeze/
Coolant Ten Year/150,000
Mile Formula OAT (Organic Additive Technology). 11.6 Quarts (11 Liters)
Engine Coolant
6.7L Turbo Diesel Engine We recommend you use
MOPAR
®Antifreeze/
Coolant Ten Year/150,000
Mile Formula OAT (Organic Additive Technology). 5.7 Gallons (21.4 Liters)
Engine Oil with Filter
3.0L Turbo Diesel Engine –
1500 Models Only
We recommend you use
ACEA C3 5W-30 engine oil meeting Chrysler material standard MS-11106 or
Pennzoil Ultra Euro L full
synthetic 5W-30 motor oil. 10.5 Quarts (10 Liters)
Engine Oil with Filter
6.7L Turbo Diesel Engine In ambient temperatures
below 0°F (-18°C),
We recommend you use
5W-40 synthetic engine oil that meets Chrysler Materials Standard
MS-10902 and the API
CJ-4 engine oil category is
required such as MOPAR
®,
Shell Rotella®and
Shell Rimula®.
In ambient temperatures above 0°F (-18°C),
We recommend you use 15W-40 engine oil that
meets Chrysler Materials
Standard MS-10902 and the API CJ-4 engine oil
category is required such
as MOPAR
®, Shell Rotella®
and Shell Rimula®. 12 Quarts (11.4 Liters)
MAINTAINING YOUR VEHICLE
209

ComponentFluid, Lubricant, or
Genuine Part Capacities
Engine Oil Filter
3.0L, 6.7L Diesel Engine We recommend you
use MOPAR
®Engine
Oil Filters. —
Engine Fuel Filter
3.0L Turbo Diesel –
1500 Models Only We recommend you use
MOPAR
®Fuel Filter.
Must meet 3 micron rating. Using a fuel filter that does
not meet the manufacturers
filtration and water separat- ing requirements can
severely impact fuel system life and reliability. —
Engine Fuel Filter
6.7L Turbo Diesel We recommend you use
MOPAR
®Fuel Filter.
Must meet 3 micron rating. Using a fuel filter that does
not meet the manufacturers
filtration and water separat- ing requirements can
severely impact fuel system life and reliability. —
Crankcase Ventilation Filter
6.7L Turbo Diesel We recommend you use
MOPAR
®CCV Filter. —
Automatic Transmission –
Eight-Speed Automatic
3.0 Turbo Diesel –
1500 Models Only We recommend you use
MOPAR
®ZF 8&9 Speed
ATF™ Automatic
Transmission Fluid. —
Automatic Transmission –
Six-Speed Automatic –
68RFE We recommend you use
MOPAR
®ATF+4®Auto-
matic Transmission Fluid. —
Automatic Transmission –
Six-Speed AISIN HD
Automatic MOPAR
®ASRC Automatic
Transmission Fluid or equivalent. —
Clutch Linkage We recommend you use
MOPAR
®Multi-Purpose
Grease, NLGI Grade 2 E.P. —
Manual Transmission
G-56 – 6.7L Diesel Engine We recommend you use
MOPAR
®ATF+4®Auto-
matic Transmission Fluid. —
Transfer Case We recommend you use
MOPAR
®BW44–44
Transfer Case Fluid. —
MAINTAINING YOUR VEHICLE
212

CAUTION!
• Mixing of engine coolant (antifreeze) other than specified Organic AdditiveTechnology (OAT) engine coolant (antifreeze), may result in engine damage and
may decrease corrosion protection. Organic Additive Technology (OAT) engine
coolant is different and should not be mixed with Hybrid Organic Additive
Technology (HOAT) engine coolant (antifreeze) or any “globally compatible”
coolant (antifreeze). If a non-OAT engine coolant (antifreeze) is introduced into
the cooling system in an emergency, the cooling system will need to be drained,
flushed, and refilled with fresh OAT coolant (conforming to MS-12106), by an
authorized dealer as soon as possible.
• Do not use water alone or alcohol-based engine coolant (antifreeze) products. Do not use additional rust inhibitors or antirust products, as they may not be
compatible with the radiator engine coolant and may plug the radiator.
• This vehicle has not been designed for use with propylene glycol-based engine coolant (antifreeze). Use of propylene glycol-based engine coolant (antifreeze)
is not recommended.
E-85 Flexible Fuel — 3.6L Engine Only
CAUTION!
Only vehicles with the E-85 fuel filler door label or a yellow gas cap can operate on
E-85.
Refer to your Owner's Manual on the DVD for further details.
MAINTENANCE SCHEDULE — GASOLINE ENGINE
Your vehicle is equipped with an automatic oil change indicator system. The oil
change indicator system will remind you that it is time to take your vehicle in for
scheduled maintenance.
Based on engine operation conditions, the oil change indicator message will
illuminate. This means that service is required for your vehicle. Operating conditions
such as frequent short-trips, trailer tow, extremely hot or cold ambient temperatures,
and E85 fuel usage will influence when the “Oil Change Required” message is
displayed. Severe Operating Conditions can cause the change oil message to
illuminate as early as 3,500 miles (5,600 km) since last reset. Have your vehicle
serviced as soon as possible, within the next 500 miles (805 km).
MAINTAINING YOUR VEHICLE
214

Your authorized dealer will reset the oil change indicator message after completing
the scheduled oil change. If a scheduled oil change is performed by someone other than
your authorized dealer, the message can be reset by referring to the steps described
under “Instrument Cluster Warning Lights” in “What To Do In Emergencies” in this
guide or “Electronic Vehicle Information Center (EVIC)” in “Understanding Your
Instrument Panel” in your Owner’s Manual on the DVD for further information.
NOTE:
•1500 Models Only
Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km)
or twelve months on 1500 trucks, whichever comes first.
•2500 – 3500 Models
Under no circumstances should oil change intervals exceed 8,000 miles (13,000 km)
or twelve months on 2500 – 3500 trucks, whichever comes first.
•Severe Duty All Models
Change Engine Oil at 4000 miles (6,500 km) if the vehicle is operated in a dusty and
off road environment. This type of vehicle use is considered Severe Duty
Once A Month Or Before A Long Trip:
• Check engine oil level
• Check windshield washer fluid level
• Check tire pressure and look for unusual wear or damage. Rotate tires at the first sign of irregular wear, even if it occurs before the oil indicator system turns on.
•
Check the fluid levels of the coolant reservoir, brake master cylinder, power steering
(2500/3500 Models Only) and automatic transmission (six-speed only) as needed
• Check function of all interior and exterior lights
Required Maintenance
Refer to the Maintenance Schedules on the following pages for required maintenance.
At Every Oil Change Interval As Indicated By Oil Change Indicator System:
• Change oil and filter.
• Rotate the tires. Rotate at the first sign of irregular wear, even if it occurs before the oil
indicator system turns on.
• Inspect battery and clean and tighten terminals as required.
• Inspect automatic transmission fluid if equipped with dipstick.
• Inspect brake pads, shoes, rotors, drums, hoses and park brake.
• Inspect engine cooling system protection and hoses.
• Inspect exhaust system.
• Inspect engine air cleaner if using in dusty or off-road conditions.
• Lube the front drive shaft fitting (2500/3500 (4x4) models only).
MAINTAINING YOUR VEHICLE
215